How to match the rackets in your bag
To match the rackets in your bag, measure three things on each: weight, balance point and swing weight. Then add weight to the rackets that fall short until the numbers agree, so that picking up the spare racquet when a string breaks changes nothing.
Why the same model can feel different
Rackets of the same model come off the production line a little different: a little heavier or lighter, with the weight a little further up or down the frame.
Weight and balance alone don’t settle it. Swing weight, how hard a racket is to swing, depends on how far the weight is spread along the frame, not only on how much there is and where it balances. Two rackets can weigh the same and balance at the same point, yet one carries a little more at both ends, and that one is harder to swing. So measure swing weight too: it says how heavy each racket feels in motion.
Match the frames, not what is on them
What you are correcting is the frames, so match them with as little on them as you can: ideally bare, with no strings, grip or overgrip. Whatever goes on afterwards adds the same to each racket’s weight, balance and swing weight, as long as it is the same thing in the same place. So matched frames stay matched once strung with the same string and finished with the same grip and overgrip. The tension doesn’t come into it: it changes how the strings play, not how much the racket weighs or where the weight sits.
The swing weight rig hangs a racket by its top cross string, so for that number the frames need strings. String them the same way, leave off overgrips and dampeners, and the difference you measure is still the frames’.
The three numbers to compare
-
Weight. Weigh each racket on a kitchen scale, to the gram.
-
Balance point. Rest the racket across a single pen or the edge of a ruler, slide it until it sits level, and measure from the butt cap to that point, to the millimetre. Measure every racket the same way: a millimetre out moves its swing weight by about two points.

-
Swing weight. Hang each racket head-up from two rods at the edge of a table and time its swing. How to measure swing weight at home gives the steps and the sums. Compare results quoted about the same point: the standard is 10 cm from the butt cap, but some stringers use another.
Bring them into line
Weight is easy to add and hard to take off, so pick the racket the others should match, usually the one with the highest numbers, and bring the rest up to it. On the frame, from the tip down to the throat, and under the grip, weight goes on as thin self-adhesive strips of lead or tungsten tape. In the butt cap, it goes in as lead or tungsten putty. Where it goes decides what it changes:
- At the tip, 12 o’clock on the head: the most swing weight for each gram, and the balance moves towards the head.
- At the balance point: weight without moving the balance.
- Under the grip: weight with hardly any swing weight, and the balance moves towards the handle.
- In the butt cap: the balance moves furthest towards the handle for each gram, with very little swing weight.
Swing weight is measured about a point 10 cm from the butt cap, and what added weight brings grows with the square of its distance from that point. For g grams added x cm from the butt cap, on a racket that weighed W grams and balanced at b cm:
- Swing weight added, in kg·cm²: g × (x − 10)² ÷ 1,000.
- New balance point, in cm: (W × b + g × x) ÷ (W + g).
So a gram near the tip, say 67 cm from the butt cap, adds about 3 points, while a gram at a 32 cm balance point adds about half a point.
Say racket A weighs 318 g, balances at 32.6 cm and swings at 322, and racket B weighs 316 g, balances at 32.4 cm and swings at 316. B needs 2 g and 6 points. Two grams at its tip add about 6.5 points and move its balance to 32.6 cm: one strip matches all three numbers.
Rackets are rarely that tidy, so add a little at a time and measure all three again after each change.
Sometimes the lighter racket can’t be brought up alone: the weight it needs, put where its balance needs it, brings more swing weight than it lacks, or its balance has further to move than that much weight can shift it. Then add some to the other racket too. With weight on both, the three numbers can always be made to agree, though both rackets end up a little heavier.
Where RacketCheck does the work
RacketCheck measures swing weight, with the phone’s camera timing the racket on the rig. The swing weight is worked out from the weight and balance you enter, so after adding weight, weigh the racket and find its balance again before measuring.
Measuring is free, with every number shown, and the free version keeps one racket. To compare a bag with it, measure the rackets one at a time, entering each one’s weight, balance and hang point in the swing weight setup, and note the results.
With RacketCheck Pro you can keep as many rackets as you own. Each keeps its own weight, balance and notes, such as where the weight went, and its own hang point, so the rig is measured once. Every swing weight is saved with the weight and balance it was worked out from, so a racket’s history shows what each change did, and the garage shows each racket’s latest swing weight, so the whole bag reads at a glance.